cppcheck found a leaked file descriptor in the debugging code
enabled by defining ENTROPY_STATS. Fixes issue #60.

Change-Id: I0c1d0669cb94d44fed77860f97b82763be06b7cb

there were four versions for the regular and
macroblock loopfilters:
horizontal [y|uv]
vertical [y|uv]

this moves all the common code into 2 functions:
vp8_loop_filter_neon
vp8_mbloop_filter_neon

this provides no gain in performance. there's a bit
of jitter, but it trends down ~0.25-0.5%. however,
this is a huge gain maintenance. also, there is the
potential to drop some stack usage in the macroblock
loopfilter.

Change-Id: I91506f07d2f449631ff67ad6f1b3f3be63b81a92

The primary goal is to allow a binary to be built which supports
 NEON, but can fall back to non-NEON routines, since some Android
 devices do not have NEON, even if they are otherwise ARMv7 (e.g.,
 Tegra).
The configure-generated flags HAVE_ARMV7, etc., are used to decide
 which versions of each function to build, and when
 CONFIG_RUNTIME_CPU_DETECT is enabled, the correct version is chosen
 at run time.
In order for this to work, the CFLAGS must be set to something
 appropriate (e.g., without -mfpu=neon for ARMv7, and with
 appropriate -march and -mcpu for even earlier configurations), or
 the native C code will not be able to run.
The ASFLAGS must remain set for the most advanced instruction set
 required at build time, since the ARM assembler will refuse to emit
 them otherwise.
I have not attempted to make any changes to configure to do this
 automatically.
Doing so will probably require the addition of new configure options.

Many of the hooks for RTCD on ARM were already there, but a lot of
 the code had bit-rotted, and a good deal of the ARM-specific code
 is not integrated into the RTCD structs at all.
I did not try to resolve the latter, merely to add the minimal amount
 of protection around them to allow RTCD to work.
Those functions that were called based on an ifdef at the calling
 site were expanded to check the RTCD flags at that site, but they
 should be added to an RTCD struct somewhere in the future.
The functions invoked with global function pointers still are, but
 these should be moved into an RTCD struct for thread safety (I
 believe every platform currently supported has atomic pointer
 stores, but this is not guaranteed).

The encoder's boolhuff functions did not even have _c and armv7
 suffixes, and the correct version was resolved at link time.
The token packing functions did have appropriate suffixes, but the
 version was selected with a define, with no associated RTCD struct.
However, for both of these, the only armv7 instruction they actually
 used was rbit, and this was completely superfluous, so I reworked
 them to avoid it.
The only non-ARMv4 instruction remaining in them is clz, which is
 ARMv5 (not even ARMv5TE is required).
Considering that there are no ARM-specific configs which are not at
 least ARMv5TE, I did not try to detect these at runtime, and simply
 enable them for ARMv5 and above.

Finally, the NEON register saving code was completely non-reentrant,
 since it saved the registers to a global, static variable.
I moved the storage for this onto the stack.
A single binary built with this code was tested on an ARM11 (ARMv6)
 and a Cortex A8 (ARMv7 w/NEON), for both the encoder and decoder,
 and produced identical output, while using the correct accelerated
 functions on each.
I did not test on any earlier processors.

Change-Id: I45cbd63a614f4554c3b325c45d46c0806f009eaa

onyx_if is getting pretty big. split out the temporal code to make it
easier to look at.

Change-Id: I207c3a94c90e91b32e3ea5e1836a53b7a990fabd

The code was not checking for frame sizes smaller than 3 bytes, and the
 partition size checks might have failed if the input buffer was within
 16MB of the top of the heap.
In addition, the reference count on the current frame buffer was not
 being decremented on error, so after a small number of errors, no new
 frame buffer could be found and it would run off the list of them.

Change-Id: I0c60dba6adb1e2a29df39754f72a56ab6c776b46

Most of the code that actually uses these matrices indexes them as
 if they were a single contiguous array, and coverity produces
 reports about the resulting accesses that overflow the static
 bounds of the first row.
This is perfectly legal in C, but converting them to actual [16]
 arrays should eliminate the report, and removes a good deal of
 extraneous indexing and address operators from the code.

Change-Id: Ibda479e2232b3e51f9edf3b355b8640520fdbf23

Change the pts of the altref frame to be as close as possible to the
pts of the preceding frame and still be strictly increasing.

Change-Id: Iae3033a4c89ae5a9d0e5c4198e9196e5f3ee57c7

The first implementation of the firstpass motion map for motion
compensated temporal filtering created a file, fpmotionmap.stt,
in the current working directory. This was not safe for multiple
encoder instances. This patch merges this data into the first pass
stats packet interface, so that it is handled like the other
(numerical) firstpass stats.

The new stats packet is defined as follows:
    Numerical Stats (16 doubles) -- 128 bytes
    Motion Map                   -- 1 byte / Macroblock
    Padding                      -- to align packet to 8 bytes

The fpmotionmap.stt file can still be generated for debugging
purposes in the same way that the textual version of the stats
are available (defining OUTPUT_FPF in firstpass.c)

Change-Id: I083ffbfd95e7d6a42bb4039ba0e81f678c8183ca

Change-Id: Ia649b500ef020225d8bbf611799d0f47658dc2ac

This rewriting reflects changes made in commit "Improve the
accuracy of forward walsh-hadamard transform". Since this function
is not called much, only a small encoder performance gain (~0.5% )
is seen.

Change-Id: Ie9df58a43028a11fd5b115c4bbe3141f7596578b

Change-Id: I8eb49c56f7509f0a8074d440e8345b9e3344b85b

Instead of doing 8-bit data unpack and 16-bit subtraction, use
psubb to do 16 8-bit subtractions and pcmpgtb to preserve the
sign information. This does not bring noticable gain since
these functions are not called frequently.

Change-Id: I90a0dfaa3db9d422e4ada324076596ffb178548e

generic version got fixed, but not the arm version. fixes:
vp8/encoder/arm/mcomp_arm.c: In function 'vp8_full_search_sadx3':
vp8/encoder/arm/mcomp_arm.c:1208: warning: pointer targets in passing
argument 5 of 'fn_ptr->sdx3f' differ in signedness
vp8/encoder/arm/mcomp_arm.c:1208: note: expected 'unsigned int *' but
argument is of type 'int *'

and another unsigned change to keep the files similar

Change-Id: I1b6255dc3a03b90394a791ee0d15d8167d9454db

vp8_diamond_search_sadx4 isn't used in arm because there is no
corrosponding sdx4df as in x86. rather than keep it in sync with
../mcomp.c, delete it

vp8_hex_search had the original, more readable/understandable code if`d
out. it's also available in ../mcomp.c, so remove the dead copy

Change-Id: Ia42aa6e23b3a2e88040f467280befec091ec080e

when a subsequent frame is encoded as an alt reference frame, it is
unlikely that any mb in current frame will be used as reference for
future frames, so we can enable quantization optimization even when
the RD constant is slightly rate-biased. The change has an overall
benefit between 0.1% to 0.2% bit savings on the test sets based on
vpxssim scores.

Change-Id: I9aa7bc5cd573ea84e3ee655d2834c18c4460ceea

../libvpx/vp8/encoder/bitstream.c: In function ‘pack_inter_mode_mvs’:
../libvpx/vp8/encoder/bitstream.c:1026: warning: array subscript has type ‘char’

Change-Id: Ic77491e0a172fa1821e5b3e914d0dc41fe87c00f

In order to know if all 4/8 neighbor points are within the bounds,
4 bounds checking are enough instead of checking 4 bounds for
each points (16/32 checkings). This improvement reduces cost of
vp8_diamond_search_sadx4() by 30%, and gives encoder a 1.5%
performance gain (test options: 1 pass, good, speed=4).

Change-Id: Ie8da29d18a6ecfc9829e74ac02f6fa70e042331a

Typo had function defined as _ssse2 and prototyped as _sse2.

Change-Id: If9f19da1a83cff40774a90cf936d601c0bf1b7fe

QWORD was being undefined because it was being used
incorrectly.

Change-Id: I3610cefa3d6f0da4054316760f78b9694cde3876

This patch moves the scattered updates to the mb skip state
(mode_info_context->mbmi.mb_skip_coeff) to vp8_tokenize_mb. Recent
changes to the quantizer exposed a bug where if a macroblock
could be coded as a skip but isn't, the encoder would run the
loopfilter but the decoder wouldn't, causing a reference buffer
mismatch.

The loopfilter is controlled by a flag called dc_diff. The decoder
looks at the number of decoded coefficients when setting this flag.
The encoder sets this flag based on the skip state, since any
skippable macroblock should be transmitted as a skip. The coefficient
optimization pass (vp8_optimize_b()) could change the coefficients
such that a block that was not a skip becomes one. The encoder was
not updating the skip state in this situation for intra coded blocks.

The underlying issue predates it, but this bug was recently triggered
by enabling trellis quantization on the Y2 block in commit dcd29e36,
and by changing the quantizer range control in commit 305be4e4.

Change-Id: I5cce5da0dbc2d22f7d79ee48149f01e868a64802

These functions should never change their input, and there's no
 reason not to declare that.
This allows them to be passed static const data.

Change-Id: Ia49fe4b01e80e9afcb24b4844817694d4da5995c

There is currently no inexact version of this function, so do not
 even compile it without EXACT_QUANT.
This will prevent someone from inadvertently trying to use it without
 the proper EXACT_QUANT setup.

Change-Id: Ia13491e0128afb281c05c9222ee5987101e4010d

This is just eliminating some cruft.
Although a number of variables are declared only when INTRARDOPT
 is defined, they are used elsewhere without that protection, and
 no longer just for intra RDO.
The intra_rd_opt flag was hard-coded to 1 and never checked.

Change-Id: I83a81554ecee8053e7b4ccd8aa04e18fa60f8e4f

Remove vp8/encoder/x86/csystemdependent.c

Change-Id: I7c590dcd07b68704d463a1452f62f29ffb1402f4

Moved vp8_fast_quantize_b_sse from quantize_mmx.asm into
quantize_sse2.asm and renamed.  Updated the assembly code to
match the C version.

Change-Id: I1766d9e1ca60e173f65badc0ca0c160c2b51b200

As the zbin and rounding constants are normalized, rounding effectively
does the zbinning, therefore the zbin operation can be removed. In
addition, the memset on the two arrays are no longer necessary.

Change-Id: If39c353c42d7e052296cb65322e5218810b5cc4c

Filed for nasm as:
https://sourceforge.net/tracker/?func=detail&atid=106208&aid=3081103&group_id=6208

nasm just does not accept any size parameter for movhps:
1.asm:2: error: mismatch in operand sizes

Some parts of libvpx already use MMWORD for movhps and MMWORD is
defined-out so it is compatible both with yasm and nasm.

Provide nasm compatibility. No binary change by this patch with yasm on
{x86_64,i686}-fedora13-linux-gnu.

Change-Id: I4008a317ca87ec07c9ada958fcdc10a0cb589bbc

nasm does not support `label wrt rip', it requires `rel label'. It is
still fully compatible with yasm.

Provide nasm compatibility. No binary change by this patch with yasm on
{x86_64,i686}-fedora13-linux-gnu. Few longer opcodes with nasm on
{x86_64,i686}-fedora13-linux-gnu have been checked as safe.

Change-Id: I488773a4e930a56e43b0cc72d867ee5291215f50

nasm requires the instruction length (movd/movq) to match to its
parameters. I find it more clear to really use 64bit instructions when
we use 64bit registers in the assembly.

Provide nasm compatibility. No binary change by this patch with yasm on
{x86_64,i686}-fedora13-linux-gnu. Few longer opcodes with nasm on
{x86_64,i686}-fedora13-linux-gnu have been checked as safe.

Change-Id: Id9b1a5cdfb1bc05697e523c317a296df43d42a91

Raised by Lei Yang, the Y plane stride was used for UV blocks.
This is clearly a typo. But as the comments in the code suggested
that this port of code has not been used yet, so the typo should
not have created any damage yet.

Change-Id: Iea895edc17469a51c803a8cc6d0fce65a1a7fc2f

This code adjust the impact of the amount and speed of motion
on GF and KF boost.

Sections with lots of slow motion will tend to have a
somewhat bigger boost and sections with fast motion may
have less.

There is a knock on effect to the selection of the active
quantizer range.

This will likely require further tuning but helps with a couple
of particularly bad edge cases.

Change-Id: Ic2449cda7305672b69acf42fc0a845b77ac98d40

Experimented with different value for Y2_RD_MULT ranging f[1, 32],
without adapting the value to MB coding mode/frame type/Q value,
4 works out best among all values, providing overall 0.1% coding
gain on the test set.

Change-Id: I6b2583a8aa5db5e7e5c65c646301909c0c58f876

If temporal filtering is enabled but a filter type is not specified
centered filter mode is used by default.

Change-Id: I87306f267c1390074c806c506a69b4ba914d92a2

Like the ARMv6 code, these functions were accessing values below
 the stack pointer, which can be corrupted by signal delivery at
 any time.

Modified the range checking of parameters used in the
AltRef temporal filter (arnr-max-frames, arnr-strength,
arnr-type) and default values for each of them.

Change-Id: Ib261028d501b9523f6e44cb4790cc52167b6e92b

This function graduated from being a test func to something that's on
by default. Rename it and remove some spurious comments that confuse
its status.

Change-Id: I689695a3ad29c35e9a72a43ec93766733ac6c20b

Loopfilter deltas are initialized to zero on keyframes in the decoder.
The values then persist from the previous frame unless an update bit
is set in the bitstream. This data is not included in the entropy
data saved by the 'refresh entropy' bit in the bitstream, so it is
effectively an additional contextual element beyond the 3 ref-frames
and the entropy data.

The encoder was treating this delta update bit as update-if-nonzero,
meaning that the value would be refreshed even if it hadn't changed,
and more significantly, if the correct value for the delta changed
to zero, the update wouldn't be sent, and the decoder would preserve
the last (presumably non-zero) value.

This patch updates the encoder to send an update only if the value
has changed from the previously transmitted value. It also forces the
value to be transmitted in error resilient mode, to account for lost
context in the event of lost frames.

Change-Id: I56671d5b42965d0166ac226765dbfce3e5301868

Allow coefficient optimization for good quality speed 0.

Change-Id: Id0cb363df6823c6798671584fbba097916a7df2c

Moved the bounds computation on vertical MV component out
of the loop that processes MBs within a MB row.

Create  look up tables for controlling the active quantizer range.
Some initial tuning to improve quality circa 0.5% on test set.
Clean up of some stats output code

Change-Id: Ia698a8525f8b8129a503cadace3ee73fe888f543